非柔性连接石化储罐配管温差应力分析与对策

储罐配管在温差作用下产生热位移会导致管壁产生热应力，未采用柔性连接的配管由于热应力集中作用可能发生破漏。针对与石油化工储罐非柔性连接的配管的安全问题，应用ANSYS有限元分析软件模拟计算石化企业典型配管的热应力分布；根据不同类型配管的分析结果，提出了工程技术与管理方面的针对性安全措施。研究结果表明:温差效应对石化储罐配管热应力影响显著，随内外温差的增加，配管应力集中的区域增大，最大热应力值增大；补偿措施能够改善配管的柔性，降低配管应力；约束载荷限制配管热膨胀从而增大配管应力；三通管是多根配管接合的区域，这种复杂管道交汇处会形成明显应力集中。研究结果对于提高石油化工非柔性连接配管安全性有一定的指导意义。     

简述排污许可制下火电行业现状及发展

实施排污许可制度,是强化排污者责任、提高固定污染源环境管理效能、改善环境质量的重要制度保障。火电行业作为典型的高架固定源,先行试点实施排污许可制度。通过分析火电行业发展和环保现状,结合排污许可管理要点,简述排污许可制对火电行业发展的影响。     

Analysis of polycyclic aromatic hydrocarbons (PAHs) in airborne particles by direct sample introduction thermal desorption GC/MS

The technique of thermal desorption (TD)–GC/MS was evaluated for measuring airborne, 4–6 ring polycyclic aromatic hydrocarbons (PAHs) collected onto quartz filters. TD provides a more readily automated and sensitive alternative to traditional solvent extraction, decreasing the time/cost of analysis and reducing the risk of analyte loss or sample contamination. The developed method was successfully applied to the analysis of PAH standard solutions loaded on sorbent tubes packed with quartz wool and the graphitized carbon black sorbent Carbograph2. The optimized method showed high desorption efficiency over the whole range of target PAHs with good precision, linearity and sensitivity. The proposed method was verified on an urban dust Standard Reference Material (SRM 1649a); the experimentally determined concentrations agreed with the certified ranges (95% confidence limit) for all target compounds except benzo[a]anthracene, which fell just outside the narrow certified range. The desorption efficiency and the reproducibility of the method was evaluated by analysing pieces of real sample filters sampled from urban air for a period of 24 h. The results confirmed the homogeneity of the filter and showed high recovery efficiencies for all target PAHs.     

The Thermal Discharges From Nuclear Power Plants in Taiwan

The increasing use of sea water for industrial cooling presents a real threat to the ecological environment in the ocean. in Taiwan where many electric power plants along the coast take sea water for cooling, people are concerned seriously about nuclear power plants. There are three nuclear power plants in Taiwan. Each plant has two units for generating power. the first two are located along the northern coast of Taiwan. the third is located in Kenting National Park along the coast of southernmost Taiwan. the plants take sea water for cooling, and discharge their heated effluents to the ocean surface from the coast. the thermal effluents have variable effects on the ecological environment near the plants. Fishermen living near the power plants complain that the heated water affects the inshore fishery catch. in addition, the thermal water from the second plant is easily accumulated near the coastal zone to influence the nearby swimming area in the summer-time. the thermal water from the third plant bleaches or kills some corals in shallow water near the outlet, and this conflicts with the interests of Kenting National Park.     

双酚S在两种典型地带性土壤中的吸附/解吸行为研究

采用批平衡实验方法研究了双酚S（BPS）在两种典型地带性土壤中的吸附/解吸行为.结果表明,吸附动力学曲线符合拟二级动力学方程.吸附等温线呈非线性,且同时符合Freundlich和Langmuir方程.相比而言,BPS更易吸附在高有机质含量的黑土中,298 K反应温度下BPS在黑土和红壤上的最大吸附容量分别为497.8和156.6 mg·kg^-1.吸附到两种土壤中的BPS存在解吸滞后现象,这可能是由于BPS以化学吸附和微孔扩散的形式存在于土壤中的缘故.溶液pH与BPS在土壤中的吸附容量呈负相关关系,即中性形态的BPS比阴离子形态的BPS具有更高的吸附容量.与结构类似物双酚A（BPA）的吸附相比,BPS在土壤中的吸附量更低,因此具有更高的迁移能力,可能会引起更高的环境健康风险.本研究结果为了解BPS在土壤中的迁移规律提供了数据支持.     

酸性紫色水稻土颗粒有机质对镉的吸附特性

采集典型的酸性紫色水稻土（APPS）,从中分离出颗粒有机质（POM）,通过批量试验研究POM及其来源土壤Cd²⁺的吸附动力学、等温吸附和热力学特征,通过扫描电镜-能谱仪、傅里叶红外光谱仪等手段及吸附前后镉的形态变化的测定,研究了POM对Cd²⁺的吸附机制.结果表明：POM对Cd²⁺的亲和力远高于其来源土壤.POM及土壤对Cd²⁺的吸附动力学最优模型均为准二级动力学.Langmuir、Freundlich方程均能较好地描述其等温吸附特征,其中对POM,以Freundlich方程更优,表明POM对Cd²⁺的吸附属于多分子层的非均质吸附.吸附热力学参数△G^θ均小于0、△H^θ和△S^θ均大于0,表明吸附属于自发吸热过程.根据△H^θ值及解吸试验判定POM对Cd²⁺的吸附以化学吸附为主,土壤对Cd²⁺的吸附过程以物理吸附为主.吸附平衡后,土壤中可交换态镉比例提高,而POM中交换态和络合态镉比例增加.综上及吸附前后POM的表征结果说明,POM对Cd²⁺的吸附机制包括含氧官能团的络合、离子交换、阳离子-π键、沉淀作用和静电吸附.     

Effects of SO2 and H2O on low-temperature NO conversion over F-V2O5-WO3/TiO2 catalysts

F-V_2 O_5-WO3/Ti02 catalysts were prepared by the impregnation method.As the content of F ions increased from 0.00 to 0.35 wt.%,the NO conversion of F-V_2 O_5-WO_3/TiO_2 catalysts initially increased and then decreased.The 0.2 F-V_2 O_5-WO_3/TiO_2 catalyst(0.2 wt.% F ion)exhibited the best denitration(De-NOx) performance,with more than 95% NO conversion in the temperature range 160-360℃,and 99.0% N2 selectivity between 110 and 280℃.The addition of an appropriate amount of F ions eroded the surface morphology of the catalyst and reduced its grain size,thus enhancing the NO conversion at low temperature as well as the sulfur and water resistance of the V_2 O_5-WO3/Ti02 catalyst.After selective catalytic reduction(SCR) reaction in a gas flow containing SO_2 and H_2 O,the number of NH3 adsorption sites,active component content,specific surface area and pore volume decreased to different degrees.Ammonium sulfate species deposited on the catalyst surface,which blocked part of the active sites and reduced the NO conversion performance of the catalyst.On-line thermal regeneration could not completely recover the catalyst activity,although it prolonged the cumulative life of the catalyst.In addition,a mechanism for the effects of S02 and H_2 O on catalyst NO conversion was proposed.     

石英灯辐射加热条件下低密度碳/酚醛复合材料高温响应及分析

目的研究低密度碳/酚醛复合材料在不同地面加热实验测试响应的差异性,指导材料在实际应用环境下的高温响应分析。方法对低密度碳/酚醛复合材料开展了热流为400 kW/m~2的单侧石英灯辐射加热实验,利用热电偶测温系统测量试件在加热过程中不同位置的温度时间历程,并对试件的烧蚀形貌和微观结构进行观测。同时与热流为464k W/m~2的氧乙炔加热陶瓷板辐射加热实验结果进行对比分析,并且采用有限元方法对材料的传热传质多场耦合计算进行分析。结果对于石英灯辐射加热,在测量点升温到接近200℃时,温度响应拐点都依次出现。由于加热的辐射热源不同,在不同的辐射波段下,多孔材料吸收和发射的热量不同,短时间内氧乙炔加热陶瓷板辐射加热使材料内部升温速率比石英灯辐射加热实验的要快,但长时间加热时现象刚好相反。结论进行传热传质多场耦合计算材料高温响应时,合理确定材料宏观性能随温度的变化至关重要。     

纤维增强气凝胶复合材料高温结构转变及热稳定性研究

目的研究高温受热条件下纳米复合隔热材料的结构转变特征及热稳定性。方法采用扫描电镜、X射线衍射仪、红外光谱仪及热重仪等检测方法。结果纤维增强气凝胶材料从室温到650℃存在连续的质量损失,从室温到放热前,质量损失为1.66%;365℃开始出现放热,温度升至398℃时达到峰值,整个放热过程对应质量损失约为1.3%;从435℃放热结束开始到650℃的质量损失为1.46%。经过400℃热处理后,试样比表面积从268m~2/g增加到437m~2/g;当试样热处理温度达到600℃时,试样的比表面积明显随之降低至198m~2/g。结论 SiO_2气凝胶复合材料以无定形结构为主,存在少量的二氧化钛晶体。在400℃左右,SiO_2气凝胶结构中硅甲基Si—CH_3发生氧化,产生明显的放热峰,之后硅羟基Si—OH之间发生缩聚反应,使600℃热处理后气凝胶中Si—O—Si网络骨架强度有所提高。未处理的纤维增强气凝胶材料试样上气凝胶纳米颗粒构成的块体较为良好地包裹在玻璃纤维表面,而经过600℃的高温热处理1 h后,块体气凝胶脱离了光滑的纤维表面,气凝胶纳米粒子发生收缩,致使材料比表面积下降。     

包装箱用碳纤维增强复合材料贮存寿命研究

目的研究碳纤维增强复合材料贮存条件下的性能变化趋势和寿命评估。方法对碳纤维增强复合材料开展四个不同温度条件下的热氧老化试验,按试验周期定期取样开展冲击性能测试,对试验数据采用寿命预估方法进行处理,对材料性能进行预估。结果通过数据计算分别得到我国热带海洋、干热沙漠等典型气候条件下的碳纤维增强复合材料贮存寿命分别为17.21~35.89年。结论碳纤维增强复合材料具有较好的贮存性能,在较为严酷的热带海洋气候和给定的失效判据条件下,寿命预计为17.21年。试验和数据处理方法可以较好地预计材料的性能变化趋势和开展寿命评估。